Getting Started

From HPC Wiki
Jump to navigation Jump to search

Access or "How-to-be-allowed-onto-the-supercomputer"

Depending on the specific supercomputer, one has to either register to get a user account or write a project proposal and apply for computing resources that way. The respective pages are linked in this overview.

After this is done and login credentials are supplied, one can proceed to log-in .


Log-in or "How-to-now-actually-connect-to-the-supercomputer"

Most HPC Systems are unix-based environments with shell (commandline) access.

To log in, one usually uses ssh to reach the respective Log-in Nodes (computers reserved for people just like you that want to connect to the supercomputer). Sometimes this access is restricted, so you can only connect, when you are within the university/facility and its network. To still access the Log-in Nodes externally, one can 'pretend to be inside the network' by using a Virtual Private Network (VPN).

Once there, the user can interact with the system and run (small) programs to generally test the system/software.

File Transfer or "How-to-get-your-data-onto-or-off-the-supercomputer"

To get your data (files) onto the supercomputer or back to your local machine, there are usually different ways. Sometimes there are computers specifically reserved for this purpose called copy nodes.

If available to you, it is recommened to use these copy nodes to move data to or from the supercomputer, since this will result in a better connection and disturb other users less. Additionally the tools mentioned below might only work on these nodes. If there are no dedicated copy nodes, you can usually use the Log-in Nodes for this purpose.

Commonly used and widely supported copying tools are rsync which mirrors directories (folders) between the supercomputer and your local machine. scp which is useful for a few single files or specified file-lists, and lastly the commonly used ftp or the encrypted version sftp (or ftps). A little bit more information can be found in the File Transfer article.

Schedulers or "How-To-Run-Applications-on-a-supercomputer"

To run any significant program or workload on a supercomputer, generally schedulers are employed. Alongside the above-mentioned Log-in Nodes there are usually far more Backend Nodes in the system (computers exclusively reserved for computing, to which you cannot connect directly). A programm called scheduler decides who gets how many of those compute resources for which amount of time. Please use the scheduler for everything which is not a simple small test and only runs for a few minutes. More than 98% of the power of a supercomputer can only be accessed via the scheduler and you will block the Log-in Nodes for everybody when you run your calculations there :/

When you log into a supercomputer, you can run commands on the Log-in Nodes interactively. You type, you hit return, the command gets executed. schedulers work different: You submit a series of commands (in form of a file) and tell it, how long you think these commands will take (also in the file) and how much resources it will approximately need in terms of:

  • time: If the specified time runs out, before your application finishes and exits, it will be terminated by the scheduler.
  • compute resources: how many cpus ('calculation thingies'), sockets ('cpu-houses') and nodes ('computers')
  • memory resources: how much RAM ('very fast memory, similar to the few books you have at home')
  • how to actually execute your application

and the scheduler then runs this series of commands when there is a part of the supercomputer free, which fits your requirements. This is usually delayed (sometimes you have to wait a day or two) and not instant. Furthermore you can not change the series of commands, but just terminate 'job' and submit a new one in case of an error.

The file specifying this series of commands and the requirements is called a Jobscript and specific/different depending on the scheduler. When you have this jobscript ready with the help of jobscript-examples, colleagues or your local Support, you can submit it to the respective scheduler of your facility. The Scheduler then waits until a set of nodes (computers) are free and then allocated those to compute your 'job'. Sometimes there is (an optional) Email notification on when your job starts/finishes computation.


The requirements you specified obviously have to fit within the boundaries of the system of your facility. If you ask for more than there is, chances are, the scheduler will take your job and wait until you buy and install the missing hardware in your facility -> probably forever. Information over the available hardware can be found in the Overview of the Gauss Allianz or the documentation of the different sites. You can find more information about parallelizing programs here. Also there is an Overview of the schedulers of the different sites

Modules or "How-To-Use-Software-Without-installing-everything-yourself"

Since a lot of applications rely on 3rd party software, there is a program on most supercomputers, called the Module system. With this system, other software, like compilers or special math libraries, are easily loadable and usable. Depending on the institution, different modules might be available, but there are usually common ones like the Intel or GCC Compilers.

A few common commands, to enter into the supercomputer commandline and talk to the module system, are

module list lists loaded modules
module avail lists available (loadable) modules
module load/unload x loads/unloads module x
module switch x y switches out module x for module y

If you recurrently need lots of modules, this loading can be automated with an sh-file, so that you just have to execute the file once and it loads all modules, you need.

Parallel Programming or "How-To-Use-More-Than-One-Core"

Currently development of computers is at a point, where you can not just make a processor run faster, because the semiconductor physics simply dont work that way. Therefore the current solution is to split the work into multiple, ideally independent parts, which are then executed in parallel. Similar to cleaning your house, where everybody takes care of a few rooms, on a supercomputer this is usually done with parallel programming paradigms like Open Multi-Processing (OpenMP) or Message Passing Interface (MPI). However like the fact that you only have one vacuum cleaner in the whole house which not everybody can use at the same time, there are limits on how fast you can get, even with a big number of processing units/cpus/cores (analogous to people in the metaphor) working on your problem (cleaning the house) in parallel.